Specifications, Prices & Availability may change without notice. Images are for illustration purposes only. E&OE
12 24V Trigger Cycle Timer Delay Switch Circuit Board MOS
Transparent Acrylic Enclosure 79.5 x 64.5 x 21mm For Use With Arduino Uno
The WeMos LOLIN32 is a Development Board Built Around The ESP-WROOM-32 Microcontroller. It Boasts 4MB of Memory and Offers WiFi, Bluetooth and Lipo Battery Connector. THIS ITEM WILL FIT IN BDD ESP32 SCREW TERM B/OUT BOARD
|
|
155.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
XH-M601 Lithium Battery Charger Control Board, In (13.8-14.8VDC), Out(12VDC)
4S 40A 18650 Lithium Battery Protection Board
7S 18650 Lithium Ion Battery Protection Board with Balance 15A 29.4V
|
|
170.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
5V KY-009 RGB 3 Color LED SMD Module
Adjustable DC/DC Buck Module LM2596S I/P 3-40V O/P 1,5-35V 3A (Requires 1,5V Differential) See also BMT ADJ DC/DC MODULE 3A 1,5-35V
Adjustable DC/DC Buck Module with 3 Digit Display Using LM2596S. I/P 3-40V O/P 1,5-35V 3A (Requires 1,5V Differential)
8mm Bore Diameter Pillow Block Mounted Ball Bearing KP08
DHT11 - Pre-calibrated Digital Output Temperature and Humidity Sensor on PCB. 5VDC
JDY-23 Bluetooth 5.0 Module
K Type Thermocouple Control Temperature 0-600C Sensor
Electret Microphone Adjustable Amplifier using MAX4466. Similar to Adafruit ID:1063
2S 7.4V 8.4V 18650 Lithium Battery Protection Board 20A
Sensitivity Adjustable Vibration Switch Module using LM393. 5VDC
YF-B7 Water Flow Sensor Meter Counter Indicator
|
|
185.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
GY-530 (VL53L0X) Time Of Flight (TOF) Laser Sensor 2m. Operating Voltage: 2.8V to 5.5V.
|
|
100.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
5mm High Bright LED Kit. 20 of each- Red, Green, Blue. Yellow and White
Magician 4WD 2 Tier Robot Car Chassis Kit with Speed Encoder
|
|
259.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
ISD1820 10 sec Message/Voice Record-play Module with Mic
Steel Omni Wheel(360°). 48x32x21mm. Maximum Load 15Kg
Single Channel 5VDC Solid State Relay Board 240V/2A with Fuse
DHT22 Digital Humidity and Temperature Sensor Module on PCB, DHT22 AM2302 Module.
IR Remote Control Kit HX1838 - Uses CR2025 Battery- Not Included
SOIC8 SOP8 BIOS Programmer Adaptor Board with Test Clip and Flat Cable
2,4GHZ Transceiver Module Using Nordic NRF24L01+. SPI I/Face. Voltage: 1.9-3.6V (Recommended 3.3V), 250M Open Area, Maximum Output Power: +20DBM, Emission Mode Current(Peak): 115mA, Receive Mode Current(peak): 45mA, Power-Down Mode Current: 4.2UA
Plastic Gear Kit Including Propellors, Rubber Bands, and Window Plate
TEMT6000 Ambient Light Sensor. Maximum Sensitivity: 570 NM. Wide Half Angle Sensitivity: 60°
LM35DZ Temperature Sensor On PCB Module
4WD Smart Robot Car Chassis Kit Transparent Single Chassis
|
|
175.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
900MHz-1800MHz GPRS/GSM Antenna with SMA Male Connector
CR123A Lithium Battery Holder
110V-220V Outdoor Wide-angle Intelligent Infrared Sensor Switch Black
|
|
175.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
Welded 20mm-4Pins Board-3W-RGB
ESP32 UNO D1 R32 WIFI Bluetooth Development Board
Barometric Sensor (Temp, Air Pressure and Humidity) 3.3V
Non Contact Liquid Level Sensor NPN 5-12V
|
|
225.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
Propellor One pair black 0.8X46mm
MKII Robot Gripper with Brass Sleeved Joints. Used with MG995, SG5010 or Similar Servos
|
|
175.01
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
7DOF (GY-91) Gyro Accelerometer/Compass/Barometric Sensor. Chip: MPU9250 (6 Axis) + BMP280. The MPU-9250 Combines a 3-Axis Accelerometer and 3-Axis Gyroscope in a Single Chip. The BMP280 is a Barometric Pressure Sens
|
|
160.01
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
DC/DC Adjustable 9A 300W Step Down Buck Converter 5-40V to 1.2-35V Power Module
ESP32 Arduino LVGL WiFi & Bluetooth Development Board. 2.8Inch 240*320 Smart Display Screen. Resistive Touch
|
|
475.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
Programmable Latching Timer Module, 12V, 0-999S, with LED Display and Case
|
|
135.00
|
ZAR
|
|
|
inc
|
|
for 1 Each
|
ESP8266 NodeMCU Lua CP2102 WiFi Board. Optional Driver Expansion Board Sold Separately
WiFi NodeMcu Lua L293D Driver Board for ESP8266 ESP-12E
Towerpro Continuous Rotation Metal Gear RC Micro Servo MG90S. 360° in each direction
3D Printer Ramps 1.6 Controller Board for REPRAP. Supports: A4988 DRV8825 AND OTHER Motor Drivers and LCD: 12864 LCD/2004 LCD/ TFT3.5. Input Voltage: 12V. Power: 270W. Patch MOS Tube: B55NF06. Size: 101.5mm x 60.5mm.
12VDC 0,1A - 5015 Sleeve Bearing Cooling Fan for 3D Printer 50x50x15mm
Arduino Compatible Ethernet Shield, with Wiznet W5100 R3 Network for UNO and Mega 2560 with Micro-SD Card Slot.