SIM800 GSM GPRS ADD-ON V2.0 Module Shield [BMT RASPBERRY PI GSM/GPRS MOD V2] .::. Communica Online

Catalog > Internet of Things (IOT) Related Products > More Platforms

Raspberry PI SIM800 GSM GPRS ADD-ON V2.0 Module Shield [BMT RASPBERRY PI GSM/GPRS MOD V2]

SIM800 GSM GPRS ADD-ON V2.0 Module Shield

SIM800 / GSM / GPRS / ADD-ON / V2.0 Module Shield

Raspberry PI SIM800 GSM GPRS ADD-ON V2.0 Module Shield

Part No: BMT RASPBERRY PI GSM/GPRS MOD V2

	720.00	ZAR
		inc
for 1 Each

(Quoting) Add to Cart Buy Now

Specifications, Prices & Availability may change without notice. Images are for illustration purposes only. E&OE

Overview

SIM800 GSM GPRS Add-on V2.0 Message Module Expansion Board for Raspberry Pi

Raspberry PI GSM Add-on V2.0 is customized for Raspberry Pi interface based on SIM800 quad-band GSM/GPRS/BT module. AT commands can be sent via the serial port on Raspberry Pi, thus functions such as dialing and answering calls, sending and receiving messages and surfing on line can be realized. Moreover, the module supports powering-on and resetting via software.

Features

PWR (Power): When there is normal supply to the board, the indicator keeps on.
8STATUS (SIM800 status): When SIM800 works normally, the indicator keeps on.

NET (SIM800 network status): used to indicate network status, the working status of the indicator is as below:

OFF SIM800 does not work
64ms on/800ms off SIM800 does not find network
64ms on/3000ms off SIM800 registers the network
64ms on/300ms off GPRS communicates

Specifications

Quad-Band 850/ 900/ 1800/ 1900 MHz
GPRS multislot class 12
Operation temperature: -40°C to +85 °C
Operation Level: Digital 3.3V DC
Interface: UART
Baud rate: 9600(default)

References

Install the RPI GSM ADD-on V2.3 on the Raspi 3B (Ensure Antenna attached before power up!)
Power Pi and boot up the Pi (assuming you have a SDcard in the Pi)
Open a terminal/console/shell command line

Run these commands:
wget https://www.waveshare.com/w/upload/3/3e/SIM800C-GSM-GPRS-HAT-Demo-Code.zip
mkdir temp
cd temp
unzip /home/pi/SIM800C-GSM-GPRS-HAT-Demo-Code.zip
sudo nano /etc/rc.local

# Add this line just before "exit 0" which will be on the very last line

sh /home/pi/temp/SIM800C-GSM-GPRS-HAT-Demo-Code/Raspberry/pi_gpio_init.sh
Just for reference, pi_gpio_init.sh contains:

echo "4" > /sys/class/gpio/export
sleep 0.1
echo "out" > /sys/class/gpio/gpio4/direction
echo "0" > /sys/class/gpio/gpio4/value
sudo nano /lib/systemd/system/hciuart.service
[Unit]
Description=Configure Bluetooth Modems connected by UART
ConditionFileNotEmpty=/proc/device-tree/soc/gpio@7e200000/bt_pins/brcm,pins
Requires=dev-serial1.device
#After=dev-serial1.device
After=dev-ttyS0.device

[Service]
Type=forking
#ExecStart=/usr/bin/btuart
ExecStart = /usr/bin/hciattach /dev/ttyS0 bcm43xx 460800 noflow -

[Install]
sudo apt-get update
sudo apt-get upgrade
sudo rpi-update
reboot
minicom -b 9600 -D /dev/ttyAMA0

AT

OK
The above returning an "OK" indicate that there is modem communication
You can now setup pppd or sakis3g or wvdial or your preferred point-to-point protocol service on /dev/ttyAMA0